Super Smart Ball Bushing™ Bearings - INCH
(Open Type) For End-Supported Applications
- Specs
- Drawing
*P= Preload, C= Clearance
ΔSee chart on bottom of this page.
NOTE:
Part number is for a standard item.
Other options available: Corrosion-Resistant, Nylon Balls, Ceramic Balls or Dry-Packed.
(Dimensions in inches)
| Part Number | Nominal Dia. |
Length C |
C1 | C2 Min. |
min. Slot Width E |
Retention Hole Dia. F |
Retention Hole Loc. G |
Angle deg α |
Number of Ball Circuits |
Ball Bushing Bearing mass lb |
Working Bore Dia. T |
Recommended Housing Bore Dia. Fixed D |
Recommended Housing Bore Dia. Adjustable D |
Ball Bushing™ Bearing/LinearRace Fit Up Fixed Dia.* Housing |
Ball Bushing™ Bearing/LinearRace Fit Up Adjustable Dia.* Housing (Before Adjustment) |
DynamicΔ Load Capacity lbf |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| TSSU-8-OPN-WW | .500 | 1.250/1.230 | 1.032/1.012 | .050 | .31 | .13 | .62 | 40 | 6 | .07 | .5000/.4995 | .8755/.8750 | .8760/.8750 | .0015C/.0000 | .002C/.0000 | 360 |
| TSSU-10-OPN-WW | .625 | 1.500/1.480 | 1.125/1.095 | .055 | .34 | .11 | .13 | 30 | 8 | .09 | .6250/.6245 | 1.1255/1.1250 | 1.1260/1.1250 | .0015C/.0000 | .002C/.0000 | 620 |
| TSSU-12-OPN-WW | .750 | 1.625/1.605 | 1.285/1.255 | .055 | .41 | .14 | .13 | 30 | 8 | .13 | .7500/.7495 | 1.2505/1.2500 | 1.2510/1.2500 | .0015C/.0000 | .002C/.0000 | 1130 |
| TSSU-16-OPN-WW | 1.000 | 2.250/2.230 | 1.901/1.871 | .068 | .53 | .14 | .13 | 30 | 8 | .24 | 1.0000/.9995 | 1.5630/1.5625 | 1.5635/1.5625 | .0015C/.0000 | .002C/.0000 | 1900 |
| TSSU-20-OPN-WW | 1.250 | 2.625/2.600 | 2.031/1.991 | .068 | .62 | .20 | .19 | 30 | 8 | .43 | 1.2500/1.2494 | 2.0008/2.0000 | 2.0010/2.0000 | .0018C/.0001P | .002C/.0001P | 2350 |
| TSSU-24-OPN-WW | 1.500 | 3.000/2.970 | 2.442/2.402 | .086 | .74 | .20 | .19 | 30 | 8 | .80 | 1.5000/1.4994 | 2.3760/2.3750 | 2.3760/2.3750 | .0021C/.0000 | .0021C/.0000 | 3880 |
Load/Life Graph (Lines indicate limiting load for given BALL BUSHING Bearing)
Determining Ball Bushing Bearing Size
To determine the proper Ball Bushing bearing size, enter the chart with the maximum load of the most heavily loaded bearing and the required travel life. Mark where the two lines intersect. All Ball Bushing bearing sizes that pass through or above and to the right of this point may be suitable for this application.
Note: For the purpose of using this chart:
| Load on Most Heavily Loaded Bearing |
= | Maximum Applied Load K0 |
where:
K0 = the Load Correction Factor, which can be determined from the Polar Graph below.
Dynamic Load Capacity Correction Factor, K0
The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by the orientation of the bearing or the direction of the applied load. For dynamic load correction factors, see polar graphs below.
| TSUPER-8-OPN TSUPER-10-OPN TSUPER-12-OPN |
TSUPER-20-OPN TSUPER-24-OPN TSUPER-32-OPN |
The actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load Correction Factor K0, is found by knowing the direction of the applied load relative to the orientation of the bearing’s ball tracks and referring to the polar graph. To determine the actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table.
