Precision Steel Ball Bushing™ Bearings - INCH
(Open Type) For End-Supported Applications
- Specs
- Drawing
ΔSee chart on bottom of this page.
NOTE:
Part number is for a standard item.
Other options available: Stainless Steel Balls, Black Oxide Sleeve and Retainer, Nylon Balls, Dry-Packed, Stainless Steel (.500 through 1.000 sizes) or With Integral Wipers.
| Catalog Number | Nom. Dia. |
Length C |
Distance Between Ret. Rings C1 |
Ret. Ring Groove Min. C2 |
Working Bore Dia. T |
Recommending Housing Bore (Before Adjustment) D |
Min. Slot Width E |
Angle deg α |
Number of Ball Circuits |
Ball Bushing Bearing Mass lb |
DynamiteΔ Load Capacity lbf |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TOPN-81420 | .500 | 1.250/1.235 | .967/.951 | .046 | .5005/.4995 | .8760/.8740 | .31 | 50 | 3 | .07 | 60 |
| TOPN-101824 | .625 | 1.500/1.485 | 1.108/1.092 | .056 | .6255/.6245 | 1.1260/1.1240 | .38 | 60 | 3 | .11 | 105 |
| TOPN-122026 | .750 | 1.625/1.610 | 1.170/1.154 | .056 | .7505/.7495 | 1.2510/1.2490 | .44 | 60 | 4 | .17 | 140 |
| TOPN-162536 | 1.000 | 2.250/2.235 | 1.759/1.741 | .068 | 1.0005/.9995 | 1.5635/1.5615 | .56 | 60 | 4 | .32 | 240 |
| TOPN-203242 | 1.250 | 2.625/2.605 | 2.009/1.991 | .068 | 1.2506/1.2494 | 2.0010/1.9990 | .63 | 50 | 5 | .90 | 400 |
| TOPN-243848 | 1.500 | 3.000/2.980 | 2.415/2.397 | .086 | 1.5006/1.4994 | 2.3760/2.3740 | .75 | 50 | 5 | 1.12 | 600 |
| TOPN-324864 | 2.000 | 4.000/3.980 | 3.195/3.177 | .103 | 2.0008/1.9992 | 3.0010/2.9990 | 1.00 | 50 | 5 | 2.16 | 860 | TOPN-406080 | 2.500 | 5.000/4.975 | 3.978/3.958 | .120 | 2.5010/2.4990 | 3.7515/3.7485 | 1.25 | 50 | 5 | 4.24 | 1380 | TOPN-487296 | 3.000 | 6.000/5.970 | 4.728/4.708 | .120 | 3.0012/2.9988 | 4.5015/4.4985 | 1.50 | 50 | 5 | 7.33 | 2000 | TOPN-6496128 | 4.000 | 8.000/7.960 | 6.265/6.235 | .139 | 4.0020/3.9980 | 6.0020/5.9980 | 2.00 | 50 | 5 | 17.25 | 3800 |
Load/Life Graph (Lines indicate limiting load for given BALL BUSHING Bearing)
Determining Ball Bushing Bearing Size
To determine the proper Ball Bushing bearing size, enter the chart with the maximum load of the most heavily loaded bearing and the required travel life. Mark where the two lines intersect. All Ball Bushing bearing sizes that pass through or above and to the right of this point may be suitable for this application.
Note: For the purpose of using this chart:
| Load on Most Heavily Loaded Bearing |
= | Maximum Applied Load K0 |
where:
K0 = the Load Correction Factor, which can be determined from the Polar Graph below.
Dynamic Load Capacity Correction Factor, K0
The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by the orientation of the bearing or the direction of the applied load. For dynamic load correction factors, see polar graphs below.
| TOPN-81420 TOPN-101824 |
TOPN-122026 TOPN-162536 |
TOPN-203242 TOPN-243848 TOPN-324864 TOPN-406080 TOPN-487296 TOPN-6496128 |
Polar Graphs
The actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load Correction Factor K0, is found by knowing the direction of the applied load relative to the orientation of the bearing’s ball tracks and referring to the polar graph. To determine the actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table.
