Needle Roller Pressbearings, Drawn Cup
Inch
- Specs
- Drawing
- Installation
- Tooling
- Shaft Recommendations

• Drawn Cup Needle Roller Bearing
• Carbon Steel Retainer, Black Oxide Finish
Features:
• High-speed, high-load
• Major assembly and production savings
• No precision holes required
• Simple quick press-fit installation
• Self-aligning to ±5°
Operating Temperature:
-22°F to +248°F
NOTE: Hardened steel shaft required


INSTALLATION:
1. Punch or drill and ream a hole of diameter A in panel as specified in the Design Parameters table.
DO NOT DEBURR OR BREAK EDGE OF HOLE.
2. Place bearing assembly in hole. The slight interference fit assures centering the assembly in the mounting hole.
3. Using an anvil with diameter N, a minimum depth of O and a punch diameter of P, press the bearing assembly into the panel by constantly applying a force of F, per the table, until the assembly is flush with the panel surface.
DO NOT USE HAMMER BLOWS!
SELF-ALIGNING
NONALIGNING
Nominal Shaft Diameter |
N Anvil Dia. +.005 -.000 |
O Min. Anvil Depth |
P Min. Punch Dia. |
CL Min. Dist. Centerline to Panel Edge |
Installation Force F Cold-Rolled Steel tons |
---|---|---|---|---|---|
1/8 | .515 | .60 | .75 | .38 | 5.0 |
3/16 | .640 | .66 | .87 | .45 | 5.5 |
1/4 | .640 | .66 | .87 | .45 | 5.5 |
5/16 | .827 | .84 | 1.07 | .50 | 5.5 |
3/8 | .827 | .84 | 1.07 | .50 | 5.5 |
1/2 | 1.078 | .97 | 1.30 | .75 | 6.0 |
5/8 | 1.265 | 1.09 | 1.50 | .75 | 6.0 |
Nominal Shaft Diameter |
N Anvil Dia. +.005 -.000 |
O Min. Anvil Depth |
P Min. Punch Dia. |
CL Min. Dist. Centerline to Panel Edge |
Installation Force F Cold-Rolled Steel tons |
---|---|---|---|---|---|
1/8 | .390 | .51 | .62 | .25 | 2.0 |
3/16 | .515 | .70 | .75 | .38 | 5.0 |
1/4 | .640 | .64 | .87 | .45 | 5.5 |
5/16 | .640 | .64 | .87 | .45 | 5.5 |
3/8 | .827 | .64 | 1.07 | .50 | 5.5 |
1/2 | .890 | .70 | 1.12 | .63 | 6.0 |
9/16 | 1.078 | .94 | 1.30 | .75 | 6.0 |
3/4 | 1.265 | .83 | 1.50 | .75 | 6.0 |
SHAFT RECOMMENDATIONS:
Shafts should be hardened to Rc 58 to 64 with 16 µin. finish. Shaft ends should have radii or be chamfered.
INSTALLATION NOTES:
1. The punch must be relieved to accommodate protruding insert.
2. DO NOT PRESS BEARING ON INSERT!
Shaft Diameters
Shafts should be hardened to Rc 58 to 64 with 16 µin. finish. Shaft ends should have radii or be chamfered.
INSTALLATION NOTES:
1. The punch must be relieved to accommodate protruding insert.
2. DO NOT PRESS BEARING ON INSERT!
Shaft Diameters
Nominal Shaft Diameter |
Self-Aligning Min. Diameter |
Self-Aligning Max. Diameter |
Nonaligning Min. Diameter |
Nonaligning Max. Diameter |
---|---|---|---|---|
1/8 | .1247 | .1250 | .1247 | .1250 |
3/16 | .1872 | .1875 | .1872 | .1875 |
1/4 | .2495 | .2500 | .2495 | .2500 |
5/16 | .3120 | .3125 | .3120 | .3125 |
3/8 | .3754 | .3759 | .3745 | .3750 |
1/2 | .4995 | .5000 | .4995 | .5005 |
5/8 | .6245 | .6250 | .6245 | .6250 |
Catalog Number | Nom. I.D. |
Shaft Diameter Min. |
Shaft Diameter Max. |
A Panel Hole |
C Flange Dia. |
E Height |
Max. Speed rpm |
Max. Radial Load lbf |
---|---|---|---|---|---|---|---|---|
BDNRSS-SAS125 | 1/8 | .1247 | .1250 | .500 | .56 | .37 | 31500 | 240 |
BDNRSS-SAS187 | 3/16 | .1872 | .1875 | .625 | .69 | .43 | 21000 | 630 |
BDNRSS-SAS250 | 1/4 | .2495 | .2500 | .625 | .69 | .43 | 44000 | 570 |
BDNRSS-SAS312 | 5/16 | .3120 | .3125 | .812 | .88 | .60 | 35500 | 650 |
BDNRSS-SAS375 | 3/8 | .3745 | .3750 | .812 | .88 | .60 | 29500 | 650 |
BDNRSS-SAS500 | 1/2 | .4995 | .5000 | 1.063 | 1.13 | .77 | 22000 | 1040 |
BDNRSS-SAS625 | 5/8 | .6245 | .6250 | 1.250 | 1.31 | .85 | 17600 | 1830 |