| |
Products >> Thomson Linear Motion >> Super Smart Ball Bushing Bearings, Open Type |
|
|
 |
|
(Single and Twin) for End-Supported Application
SUPER SMART BALL BUSHING™ PILLOW BLOCKS – INCH
|
|
|
| |
ΔSee chart on bottom of this page.
NOTE:
Part number is for a standard item.
Other options available: Corrosion-Resistant, Nylon Balls, Ceramic Balls or Dry-Packed.
|
| |
| Part Number |
Nominal
Diameter |
B |
E
± .010 |
L |
D |
V |
G1 |
S
Hole
Dia. |
Pillow
Block
mass
lb |
DynamicΔ
Load
Capacity
lbf |
Super Smart Ball Bushing™
FLANGED SINGLE PILLOW BLOCKS
(Dimensions in inches) |
| TSS6UFB-8 |
.500 |
1.63 |
1.250 |
1.69 |
1.25 |
.25 |
.72 |
.19 |
.23 |
265 |
| TSSUFB-12 |
.750 |
2.38 |
1.750 |
2.06 |
1.75 |
.38 |
.89 |
.22 |
.52 |
1130 |
| TSSUFB-16 |
1.000 |
2.75 |
2.125 |
2.81 |
2.25 |
.50 |
1.27 |
.28 |
1.04 |
1900 |
| TSSUFB-20 |
1.250 |
3.50 |
2.750 |
3.63 |
3.00 |
.63 |
1.67 |
.35 |
2.34 |
2350 |
| TSSUFB-24 |
1.500 |
4.00 |
3.125 |
4.00 |
3.62 |
.75 |
1.86 |
.41 |
3.69 |
3880 |
Super Smart Ball Bushing™
FLANGED TWIN PILLOW BLOCKS
(Dimensions in inches) |
| TSS6UTFB-8 |
.500 |
1.63 |
1.250 |
3.20 |
1.25 |
.90 |
1.48 |
1/4-20 |
.45 |
530 |
| TSSUTFB-12 |
.750 |
2.38 |
1.750 |
3.95 |
1.75 |
.90 |
1.98 |
1/4-20 |
1.05 |
2260 |
| TSSUTFB-16 |
1.000 |
2.75 |
2.125 |
5.33 |
2.25 |
.90 |
2.67 |
5/16-18 |
1.95 |
3800 |
| TSSUTFB-20 |
1.250 |
3.50 |
2.750 |
6.70 |
3.00 |
.90 |
3.35 |
5/16-18 |
4.20 |
4700 |
| TSSUTFB-24 |
1.500 |
4.00 |
3.125 |
7.50 |
3.62 |
1.00 |
3.75 |
3/8-16 |
6.81 |
7760 |
|
|
| |
Load/Life Graph (Lines indicate limiting load for given BALL BUSHING Bearing)
Determining Ball Bushing Bearing Size
To determine the proper Ball Bushing bearing size, enter the chart with the maximum load of the most heavily loaded bearing and the required travel life. Mark where the two lines intersect. All Ball Bushing bearing sizes that pass through or above and to the right of this point may be suitable for this application.
Note: For the purpose of using this chart:
Load on Most Heavily
Loaded Bearing |
= |
Maximum Applied Load
K0 |
where:
K 0 = the Load Correction Factor, which can be determined from the Polar Graph below.
Dynamic Load Capacity Correction Factor, K0
The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by the orientation of the bearing or the direction of the applied load. For dynamic load correction factors, see polar graphs below. Dynamic load capacity of Twin Super Smart Flanged Pillow Blocks is based on two bearings equally loaded.
TSSUFB-12
TSSUFB-16
TSSUFB-20
TSSUFB-24
TSSUTFB-12
TSSUTFB-16
TSSUTFB-20
TSSUTFB-24 |
TSS6UFB-8
TSS6UTFB-8 |
Polar Graphs
The actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load Correction Factor K0 is found by knowing the direction of the applied load relative to the orientation of the bearing’s ball tracks and referring to the polar graph. To determine the actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table. |
|
|
|