about us    |     services    |     sitemap    |     shopping cart    |     News  
     
       
  Products >> Thomson Linear Motion >> Super Smart Ball Bushing Pillow Blocks, Closed Type    
Thomson Ball bushing pilow blocks   (Closed Type) for End-Supported Application
SUPER SMART BALL BUSHING™ PILLOW BLOCKS – INCH

 
QBC eStore Buy Shop Online

View Cart
Quote List


THOMSON PILLOW BLOCKS


Thomson Pillow Blocks Super Smart
Close Type
Thomson Pillow Blocks Super Smart
Open Type
Thomson Pillow Blocks Super Smart
Flanged Type
Thomson Pillow Blocks Super
Close Type
Thomson Pillow Blocks Super
Open Type
Thomson Pillow Blocks Super
Twin Close Type
Thomson Pillow Blocks Super
Twin Open Type
Thomson Pillow Blocks LinearRace
Support Blocks
 
  • Specs
  • Drawing
*See chart on bottom of this page.

NOTE:
Part number is for a standard item.
Other options available: Corrosion-Resistant, Nylon Balls or Ceramic Balls.

 
Thomson ball bushing pillow blocks
 
 
Super Smart Ball Bushing™ Pillow Blocks (Closed Type, Seal at Both Ends)
(Dimensions in inches)
Part Number Nominal
Diameter
A A2 B E
± .010
E1
± .010
F F1
TSS6UPB-8 .500 2.00 1.38 1.69 1.000 1.688 1.13 .25
TSSUPB-10 .625 2.50 1.75 1.94 1.125 2.125 1.44 .28
TSSUPB-12 .750 2.75 1.88 2.06 1.250 2.375 1.56 .31
TSSUPB-16 1.000 3.25 2.38 2.81 1.750 2.875 1.94 .38
TSSUPB-20 1.250 4.00 3.00 3.63 2.000 3.500 2.50 .44
TSSUPB-24 1.500 4.75 3.50 4.00 2.500 4.125 2.88 .50

Part Number G G1 H
± .003
H1 N Pillow
Block
Mass
lb
Dynamic*
Load
Capacity
lbf
Hole Bolt
TSS6UPB-8 .69 .72 .687 1.25 .16 #6 .23 265
TSSUPB-10 .88 .83 .875 1.63 .19 #8 .51 620
TSSUPB-12 .94 .89 .937 1.75 .19 #8 .62 1130
TSSUPB-16 1.19 1.27 1.187 2.19 .22 #10 1.24 1900
TSSUPB-20 1.50 1.68 1.500 2.81 .22 #10 2.57 2350
TSSUPB-24 1.75 1.86 1.750 3.25 .28 .25 3.94 3880
 
 
Load/Life Graph (Lines indicate limiting load for given Ball Bushing Pillow Block)

Thomson Products

Determining Ball Bushing Bearing Size
To determine the proper Ball Bushing bearing size, enter the chart with the maximum load of the most heavily loaded bearing and the required travel life. Mark where the two lines intersect. All Ball Bushing bearing sizes that pass through or above and to the right of this point may be suitable for this application.

Note: For the purpose of using this chart:
Load on Most Heavily
Loaded Bearing
= Maximum Applied Load
K0
where:
K0 = the Load Correction Factor, which can be determined from the Polar Graph below.

Dynamic Load Capacity Correction Factor, K0
The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by the orientation of the bearing or the direction of the applied load. For dynamic load correction factors, see polar graphs below. Dynamic load capacity of Twin Super Smart Flanged Pillow Blocks is based on two bearings equally loaded.

Thomson Products
TSSUPB-10
TSSUPB-12
TSSUPB-16
TSSUPB-20
TSSUPB-24
TSS6UPB-8

Polar Graphs
The actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load Correction Factor K0 is found by knowing the direction of the applied load relative to the orientation of the bearing’s ball tracks and referring to the polar graph. To determine the actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table.
     
 
282