Quality Bearings and Components Cart(888) 276-4787
    Products   Thomson Linear Motion   Super Ball Bushing Pillow Blocks, Closed Type, Inch

Super Ball Bushing™ Pillow Blocks - INCH

(Closed Type) For End-Supported Applications


  • Specs
  • Drawing
Thomson Super Ball Bushing Pillow Blocks, Closed Type
*See chart on bottom of this page.

NOTE:
Part number is for a standard item.
Other options available: Corrosion-Resistant, Nylon Balls, or Ceramic Balls.

(Dimensions in inches)

Thomson Super Ball Bushing Pillow Blocks

Catalog Number Nominal
Dia.
A A2 B E
± .010
E1
± .010
F F1 G G1 H
± .003
H1 N
Hole
N
Bolt
Pillow
Block
Mass
lb
DynamicΔ
Load
Capacity
lbf
TSPB-4 .250 1.63 1.00 1.19 .750 1.313 .75 .19 .61 .22 .437 .81 .16 #6 .10 60
TSPB-6 .375 1.75 1.13 1.31 .875 1.438 .88 .19 .72 .22 .500 .94 .16 #6 .13 100
TSPB-8 .500 2.00 1.38 1.69 1.000 1.688 1.13 .25 .69 .84 .687 1.25 .16 #6 .20 255
TSPB-10 .625 2.50 1.75 1.94 1.125 2.125 1.44 .28 .70 .68 .875 1.63 .19 #8 .50 450
TSPB-12 .750 2.75 1.88 2.06 1.250 2.375 1.56 .31 .94 .72 .937 1.75 .19 #8 .60 600
TSPB-16 1.000 3.25 2.38 2.81 1.750 2.875 1.94 .38 1.20 .86 1.187 2.19 .22 #10 1.20 1050
TSPB-20 1.250 4.00 3.00 3.63 2.000 3.500 2.50 .44 1.50 1.20 1.500 2.81 .22 #10 2.50 1500
TSPB-24 1.500 4.75 3.50 4.00 2.500 4.125 2.88 .50 1.75 1.25 1.750 3.25 .28 1/4 3.80 2000
TSPB-32 2.000 6.00 4.50 5.00 3.250 5.250 3.63 .63 2.12 1.58 2.125 4.06 .41 3/8 7.00 3000


Load/Life Graph (Lines indicate limiting load for given BALL BUSHING Bearing)

Thomson Products

Determining Ball Bushing Bearing Size
To determine the proper Ball Bushing bearing size, enter the chart with the maximum load of the most heavily loaded bearing and the required travel life. Mark where the two lines intersect. All Ball Bushing bearing sizes that pass through or above and to the right of this point may be suitable for this application.

Note: For the purpose of using this chart:
Load on Most Heavily
Loaded Bearing
= Maximum Applied Load
K0

where:
K0 = the Load Correction Factor, which can be determined from the Polar Graph below.

Dynamic Load Capacity Correction Factor, K0
The Dynamic Load Capacity is based on a rated travel life of 2 million inches. The actual Dynamic Load Capacity can be affected by the orientation of the bearing or the direction of the applied load. For dynamic load correction factors, see polar graphs below.

Thomson Products


TSPB-4
TSPB-6
TSPB-8
TSPB-10 TSPB-12
TSPB-16
TSPB-20
TSPB-24
TSPB-32

Polar Graphs
The actual Dynamic Load Capacity of a Ball Bushing bearing is determined by the orientation of the bearing or direction of the applied load. The load Correction Factor K0, is found by knowing the direction of the applied load relative to the orientation of the bearing’s ball tracks and referring to the polar graph. To determine the actual Dynamic Load Capacity, multiply the proper correction factor by the Dynamic Load Capacity listed in the product table.